My next woodworking project will be building a Dutch tool chest. After some searching (too many pages only show the _outside_ of the chest, this page shows you some of the potential of storing and organizing literally dozens of tools in a box you could load into your car.
I scored a (picked over) English chest off Craigslist a while back --- unfortunately, it was left open for a long while and the front bowed out, and it had some strange design choices:
- too narrow to accommodate a full-sized framing square, the back of the lid was cut open allowing it to stick out (which makes it dangerous to move)
- only one open till which is fixed, w/ an odd saw till underneath
I put it on a small wheeled moving base from Harbor Freight, and tried storing all my traditional hand woodworking tools in it, but while they all fit, the organization is lacking and usage is problematic --- can't bring myself to get rid of it though.
which sums the various strategies and their pros and cons up nicely.
Three books on this which I would recommend to any one interested in woodworking are:
- _The Toolbox Book_ by Tolpin --- a bit dated, but still full of good information _and_ measured drawings for making some of the tool chests
- _Choosing & Using Hand Tools_ by Andy Rae --- his wonderful toolchest is features in the book above, and further photos and information are included in this book
- _Virtuoso: The Tool Cabinet and Workbench of Henry O. Studley_ --- I love and hate this book --- it's an important text, and the content is great, the problem is the presentation (pedestrian micro-typography which uses uni-directional double quotes instead of double primes, x instead of a multiplication symbol, &c.) and the typos (Studley's name is mis-spelled on this dustjacket)
I'm at a point in my life where I pretty much have all the tools I need, and the struggle is remembering where they are/that I have them, so working towards making fitted tool chests/cabinets so that everything has a place, and so that each chest/cabinet/box is applicable to a particular purpose.
I don't like how the handles are on the side for most of the packout boxes, and they're very bulky (what are those aluminum bars on the corners for?) and generally too big for almost all of my tools. Waterproof is nice, but completely unnecessary for me.
I prefer the Tanos Systainer stacking boxes. They're small enough that each box can have a single purpose. For example, I have a drill, impact driver, charger, spare battery, and all of my drill bits inside one medium box (very heavy). In an XL box I have a track saw with its accessories, in a small box I have a jig saw, and in a medium box I made some wooden dividers for all my glue, wood fillers, and caulking.
Makita makes some of the older-style boxes with 4 latches that often go on sale for very cheap on Amazon, but I prefer the newer T-lock boxes because you can open a box even if it's in a stack. But the T-lock boxes are insanely expensive, so I mostly have the Makita boxes. Both styles are compatible with each other.
I considered standardizing on Packout, but they seem to only offer one two drawer units, all of which are deeper than I'd like (I really want a single layer of tools per drawer).
Some very good ideas in there that I haven't come across. Another great DIY idea I didn't see there was gluing top of mason jar to bottom of a wood plank so you can screw/unscrew the jar. I use this for storing screws and other small things.
If you're interested in this sort of thing and don't want to build your own, I'm working on https://toolwallhq.com that exactly solves this.
HD has a dual-sided compartment case with transparent lids. One side can be used to store instruments/tools in PE foam (after removing the dividers with flush cutters), leaving the other side for small parts. 10 x 12 x 1.5 inches per side. https://www.homedepot.com/p/Husky-34-Compartment-Plastic-Dou...
My favorite thing that I lucked on for part storage as some of the other commenters here have been discussing, was the local TrueValue signed a new contract with Hillman and had all of their screw and bolt cabinets replaced so they could fit in some actual quantity of metric stuff. I bought a hardware store wall worth of bins for like $250. It was and is glorious. I'm in the process of building a proper workshop after moving for more space and the rebuilding of that wall is very exciting for me.
If you need to store a lot of small parts, go to a Cabela's (or bass pro shop) and look at the fishing section, plastic boxes with anywhere from 6 to 40 small compartments. Often a far better selection than what you'd find at a home Depot or similar.
For really small SMD (electronics) parts, you need something with a completely sealed compartment. Anything with removable separators or a gap between the dividers and the lid is a no-go, or you'll be tossing a couple hundred unmarked 0805 MLCCs in the trash because your 100nF and 1uF parts got mixed up together.
The cheap SMD parts containers on AliExpress [1] are reasonably good, although the lid springs some of them will inevitably break. There's probably some professional model with better quality plastics by a reputable brand as well.
I lucked [0] into being around for an office move of a company that had gone from building physical devices to pure software, and got ~24 parts drawer units [1] for free. For the utility I get out of them, I would have bought them new, but it's hard to know that beforehand - they're expensive for what they are, and to do it right you really need a lot of them to make a uniform wall. I built custom shelves to hold them without the weight adding up, in three vertical columns floor to ceiling.
I'll occasionally see deep sales (~50%) on similar items throughout the year, since presumably the cost basis isn't that high. If I somehow lost mine or needed to expand my storage, I'd plan out some shelves for whatever size the new ones were, and buy enough to fill a few more vertical columns.
[0] They also came with a bunch of assorted stainless machine screw hardware. And this was a month or so after Radio Shack closed and I had spent a week going from store to store buying buying all the switches and lights I longed for in my childhood.
I prefer these storage bins made by Stanley. They are fairly inexpensive and the small bins are removable so that you can easily grab the whole bin of screws or whatever. This also makes them easy to re-arrange your small parts. If you look around you can find them in two sizes — a thick and thin version.
If you buy the right size boxes it works out so that a given multiple of them fits in a paper sized space you can use free filing cabinets for storage.
I picked up my storage cabinet with small drawers from a family shop wood store. It's made of wood instead of being plastic, so I placed labels to each drawer to signal the resistors, inductors, capacitors, chips and so on.
If anyone is working in a tight space, I recently found that wall control makes pegboard that are only 8in wide. [1].
They're made to be horizontal so if you flip them some of the fancy accessories that rely on the horizontal slats won't work, but the pegs are still fine, and it's a good way use otherwise wasted space on really narrow walls and corners.
I 3D printed a bunch of these[0] hangers for my cordless power tools and screwed them to the underside of a shelf. This model is for DeWalt but there’s a variation for every battery platform. Seems to work pretty well.
I feel like I have carried over some bad habits from programming to my woodworking hobby. This is a hobby that hasn't taken off because I seem to enjoy finding new ways of organising my tools. The result is I have yet to make anything of significance. It feels like I am trying to find the perfect development stack.
There are some good ideas here - I especially like the magnetic bit rack. Not a fan of peg boards and general wall hangers or an insulation foam wall hanger (seems fragile and messy) but they probably work for some people.
Cool to see this on HN
the other day I saw a variation of the PVC tool holder used for holding drills. The notch didn't go all the way through, and rotated 90 degrees, perhaps less so it would be angled up slightly (so the pipe was hanging under the supporting 2x4) although it would also work fine upright.
[+] [-] roberthahn|3 years ago|reply
https://www.lumberjocks.com/BrandonW/blog/35335
Another excellent way to store and organize your tools is in an English tool chest. https://blog.lostartpress.com/2020/04/06/anarchists-tool-che...
[+] [-] WillAdams|3 years ago|reply
- too narrow to accommodate a full-sized framing square, the back of the lid was cut open allowing it to stick out (which makes it dangerous to move)
- only one open till which is fixed, w/ an odd saw till underneath
I put it on a small wheeled moving base from Harbor Freight, and tried storing all my traditional hand woodworking tools in it, but while they all fit, the organization is lacking and usage is problematic --- can't bring myself to get rid of it though.
[+] [-] WillAdams|3 years ago|reply
https://bridgerberdel.wordpress.com/2015/01/08/thoughts-on-t...
which sums the various strategies and their pros and cons up nicely.
Three books on this which I would recommend to any one interested in woodworking are:
- _The Toolbox Book_ by Tolpin --- a bit dated, but still full of good information _and_ measured drawings for making some of the tool chests - _Choosing & Using Hand Tools_ by Andy Rae --- his wonderful toolchest is features in the book above, and further photos and information are included in this book - _Virtuoso: The Tool Cabinet and Workbench of Henry O. Studley_ --- I love and hate this book --- it's an important text, and the content is great, the problem is the presentation (pedestrian micro-typography which uses uni-directional double quotes instead of double primes, x instead of a multiplication symbol, &c.) and the typos (Studley's name is mis-spelled on this dustjacket)
I'm at a point in my life where I pretty much have all the tools I need, and the struggle is remembering where they are/that I have them, so working towards making fitted tool chests/cabinets so that everything has a place, and so that each chest/cabinet/box is applicable to a particular purpose.
[+] [-] brk|3 years ago|reply
https://www.milwaukeetool.com/Products/Storage-Solutions/PAC...
https://www.pelicanzero.com/packout-nation/
[+] [-] frosted-flakes|3 years ago|reply
I prefer the Tanos Systainer stacking boxes. They're small enough that each box can have a single purpose. For example, I have a drill, impact driver, charger, spare battery, and all of my drill bits inside one medium box (very heavy). In an XL box I have a track saw with its accessories, in a small box I have a jig saw, and in a medium box I made some wooden dividers for all my glue, wood fillers, and caulking.
Makita makes some of the older-style boxes with 4 latches that often go on sale for very cheap on Amazon, but I prefer the newer T-lock boxes because you can open a box even if it's in a stack. But the T-lock boxes are insanely expensive, so I mostly have the Makita boxes. Both styles are compatible with each other.
[+] [-] WillAdams|3 years ago|reply
[+] [-] sent-hil|3 years ago|reply
If you're interested in this sort of thing and don't want to build your own, I'm working on https://toolwallhq.com that exactly solves this.
[+] [-] ghostbrainalpha|3 years ago|reply
My dad has OCD and a little shop, if I show him your planner we not see him again for days.
[+] [-] WillAdams|3 years ago|reply
[+] [-] walterbell|3 years ago|reply
[+] [-] ethbr0|3 years ago|reply
https://www.homedepot.com/p/RIDGID-Pro-System-Gear-10-Compar...
My favorite use? Dedicating one to a go-tote of assorted fastener (nails, screws, etc), divided into the different cups.
[+] [-] WillAdams|3 years ago|reply
Currently it's overflow storage for things associated w/ my CNC machines which I'm not likely to need.
[+] [-] wcunning|3 years ago|reply
[+] [-] granjef3|3 years ago|reply
It’s the correct length and height already, you just need to trim the width of the cross supports and tap the ends again.
The HF bins are cheap and have removable inserts that index in the lid, so you can remove one, close the lid, and your parts stay in place.
For pliers and similar tools, I’m a big fan of Adam Savage’s pliers cart: https://youtu.be/TWQAYfGxsPE
[+] [-] unknown|3 years ago|reply
[deleted]
[+] [-] WillAdams|3 years ago|reply
[+] [-] walrus01|3 years ago|reply
[+] [-] terom|3 years ago|reply
The cheap SMD parts containers on AliExpress [1] are reasonably good, although the lid springs some of them will inevitably break. There's probably some professional model with better quality plastics by a reputable brand as well.
[1] https://a.aliexpress.com/_msqygpo
[+] [-] mindslight|3 years ago|reply
I'll occasionally see deep sales (~50%) on similar items throughout the year, since presumably the cost basis isn't that high. If I somehow lost mine or needed to expand my storage, I'd plan out some shelves for whatever size the new ones were, and buy enough to fill a few more vertical columns.
[0] They also came with a bunch of assorted stainless machine screw hardware. And this was a month or so after Radio Shack closed and I had spent a week going from store to store buying buying all the switches and lights I longed for in my childhood.
[1] https://www.homedepot.com/p/Akro-Mils-24-Compartment-Small-P...
[+] [-] JKCalhoun|3 years ago|reply
https://www.homedepot.com/p/Stanley-25-Compartment-Shallow-P...
Also, a cabinet for storing the organizers is an easy build for a new woodworker:
https://www.lumberjocks.com/projects/164002
[+] [-] throwaway0a5e|3 years ago|reply
[+] [-] a1o|3 years ago|reply
[+] [-] showerst|3 years ago|reply
They're made to be horizontal so if you flip them some of the fancy accessories that rely on the horizontal slats won't work, but the pegs are still fine, and it's a good way use otherwise wasted space on really narrow walls and corners.
https://www.wallcontrol.com/8in-x-32in-horizontal-galvanized...
[+] [-] walterbell|3 years ago|reply
Seville has a 24W x 18D x 66H metal cabinet with pegboard sides, https://www.sevilleclassics.com/collections/cabinets-1/produ...
[+] [-] whiw|3 years ago|reply
I use plastic picture/poster hanging grips to cover saw blades, and lengths of 4" plastic waste pipe to store dowel and metal rod.
[+] [-] JKCalhoun|3 years ago|reply
[+] [-] logical_proof|3 years ago|reply
[+] [-] evan_|3 years ago|reply
[0]: https://www.printables.com/model/203909-dewalt-tool-mounts
[+] [-] mhb|3 years ago|reply
[+] [-] camtarn|3 years ago|reply
I just wish I had enough battery power tools that I needed to store them in such a fashion ;) Sadly most of my tools are still mains powered.
[+] [-] mmsimanga|3 years ago|reply
[+] [-] dieselgate|3 years ago|reply
[+] [-] CraigJPerry|3 years ago|reply
/me checks plywood prices in UK...
Nope.
[+] [-] failrate|3 years ago|reply
[+] [-] ComputerCat|3 years ago|reply
[+] [-] ksherlock|3 years ago|reply
[+] [-] srdixon|3 years ago|reply
[+] [-] aaron695|3 years ago|reply
[deleted]