Yes. This is already done. It's how almost all submarine communication cables currently work. Most long-distance fibre links do not use electronics to regenerate their signals.
They use optical amplifiers, which take light at one wavelength and use it to intensify light at another wavelength. They're much like lasers (technically I think they count as optically-pumped lasers?), and they turn on from a very small input signal, effectively reenforcing it.
This can happen across multiple signals, on different wavelengths, in parallel. Like a broadband radio amplifier, it boosts everything across a large working bandwidth. There are even optical compressors (also powered by light), which speed up the baud rate of signals. That way a slow electronic system can produce the original pulses, and then they can be compressed to faster than electronics can work with, and then multiplexed with many other signals at different wavelengths, and this whole composite thing is sent down the line, amplified without decoding along the way, and then finally the whole thing is reversed at the other end.
This is the trick behind how fibre links are so fast, considering there are no electronics that can handle data serially at those speeds.
You're right about submarine fibers, but you seem to suggest that the pump light for the laser amplifiers is transmitted through the fiber from the cable landing point - like the technology discussed in the OP.
That is certainly not the case, the pump light is generated from electricity right where the laser amplifier sits in the fiber. No real amounts of energy are sent optically down the fiber. To power the amplifier, a high voltage DC line is designed right into the submarine fiber cable. And those things carry a lot of power, a long fiber cable will draw tens of kilowatts of DC for all the optical repeaters.
The reason is, of course, that thousands of miles of cable has a pretty insane optical attenuation, no matter what you do, because optical attenuation rises exponentially with length. The electrical resistance of a high voltage DC power line only rises linearily, on the other hand.
Efficiency of laser diodes goes down quite a bit with bandwidth. More importantly you typically want the data going the other way (from the powered sensor). If you would use the same fibre for both directions (might be done for space constraints) the issue of using the same wavelength is that there are scattering processes (some fundamental to how fibres work) in the fibre that will cause some light to be back scattered and act like noise essentially. Your sensor would transmit with only very little power so the SNR might be completely destroyed by the back scatter of the high power piwer delivery light. If they are at different wavelengths they can be easily separated.
I was thinking that the "power extraction" might attenuate the signal too much, and it would probably lower the power output since you need to modulate the light to transmit data, instead of having it on full brightness all the time. But maybe it would work for certain applications!
There's PSK and the likes which mess with phase but I don't think that's the same as what you're asking as you would typically then use something else to actually get separate streams with it. The problem with pure and plain phase division multiplexing is how do you separate it back out on the other side? You can make up as many pairs of wave values to create the resulting wave without doing something else beyond plain multiple phases.
Time division multiplexing and frequency or amplitude division multiplexing preclude most things because they are so cheap and simple these days. Polarity is also another knob to mess with when you need to squeeze more.
retrac|2 years ago
They use optical amplifiers, which take light at one wavelength and use it to intensify light at another wavelength. They're much like lasers (technically I think they count as optically-pumped lasers?), and they turn on from a very small input signal, effectively reenforcing it.
This can happen across multiple signals, on different wavelengths, in parallel. Like a broadband radio amplifier, it boosts everything across a large working bandwidth. There are even optical compressors (also powered by light), which speed up the baud rate of signals. That way a slow electronic system can produce the original pulses, and then they can be compressed to faster than electronics can work with, and then multiplexed with many other signals at different wavelengths, and this whole composite thing is sent down the line, amplified without decoding along the way, and then finally the whole thing is reversed at the other end.
This is the trick behind how fibre links are so fast, considering there are no electronics that can handle data serially at those speeds.
pbmonster|2 years ago
That is certainly not the case, the pump light is generated from electricity right where the laser amplifier sits in the fiber. No real amounts of energy are sent optically down the fiber. To power the amplifier, a high voltage DC line is designed right into the submarine fiber cable. And those things carry a lot of power, a long fiber cable will draw tens of kilowatts of DC for all the optical repeaters.
The reason is, of course, that thousands of miles of cable has a pretty insane optical attenuation, no matter what you do, because optical attenuation rises exponentially with length. The electrical resistance of a high voltage DC power line only rises linearily, on the other hand.
raphman|2 years ago
cycomanic|2 years ago
dthul|2 years ago
CoastalCoder|2 years ago
zamadatix|2 years ago
Time division multiplexing and frequency or amplitude division multiplexing preclude most things because they are so cheap and simple these days. Polarity is also another knob to mess with when you need to squeeze more.