[dugmartin]

The "design for unmaintainability" problem has been around for a while. I remember helping a friend change his plugs on this Ford Ranger in the early 90s. The closest two plugs to the firewall required you to climb into the engine bay and basically hug the engine to get your arm into position to blindly get to the plugs. If you look around on YouTube you'll see some crazy mechanic videos where they show things like bolts located in impossible to loosen locations.

Cars used to be simpler to work on because a) they inherently were simpler and b) the engine bay used to have a lot of room to work in. Both of these things are not coming back.

[yobbo]

> Cars used to be simpler to work on because

No, it's because they are designed to be assembled from complete sub-assemblies. Maintenance is not assumed to be done on the sub-assemblies while they are in the final product. Under warranty, workshops are intended to replace entire sub-assemblies with new/rebuilt parts.

It's effectively a deliberate decision from the 80s that enabled faster assembly while warranties were shorter. For cars that are out of warranty, it doesn't matter either way.

The problem in the article occurs when Ford tries to pay someone to repair faults that were not planned to happen during the warranty time. Impossible, because it's completely uneconomical.

[Survived]

For cars that are out of warranty, it is an advantage, as the car will be scrapped sooner, thereby opening up a hole in the market that needs to be filled with a new car.

An advantage to the manufacturer, that is. For the consumer, it leads to never ending car payments for life, or surprise bills that approach the cost of a replacement vehicle.

[pengaru]

I've encountered these headaches helping friends with their vehicles, and every time I'm reminded how much I prefer wrenching on my 80s-90s era mazdas.

My old protege even had an access port in the fender well added specifically to remove the crank bolt with an extension. If it were an Audi the FSM would point you to the engine removal process as step 1.

[burnt-resistor]

It's kind of always been that way to varying degrees. In the 70's/80's, changing the Porsche 911 spark plugs required dropping the engine.

Also, in addition to planned obsolescence and repair hostility is Design for Manufacturing (DfM) that doesn't care about maintainability, safety, comfort, or durability, only lowest cost to shove things together on an assembly line. This is why there are some cars that require removing the wheel well to change the oil filter and other that have things completely out-of-order or require absurd tools to service. My grandfather was a 30 year Chrysler dealer mechanic who had a dozen or so custom tools for very specific purposes.

Source: Dad had an A/C & electrical mechanic shop next to a Porsche specialist shop.

[potato3732842]

>Also, in addition to planned obsolescence and repair hostility is Design for Manufacturing (DfM) that doesn't care about maintainability, safety, comfort, or durability, only lowest cost to shove things together on an assembly line.

Exactly. It's basically fight club math. Spend $10 on a click-fit connector that can't be disassembled but that a $60/hr (though they only see a fraction of that) UAW laborer can plug in in half the time can't easily short-insert that can be visually checked.

The fact that it costs $200 the 1/10000 times it fails under warranty doesn't matter with those numbers. And you don't even care about the 100/100 times it fails at 2-3x the warranty period.

Of course, you're burning credibility doing this. But credibility doesn't have an obvious mapping to a number and stonk go up, KPI go up, bonus get paid, nobody cares.

[robohoe]

Luckily you don't have go drop the engine to change spark plugs on modern water cooled Porsche 911s, but let me tell you about changing plugs on mid-engined Cayman/Boxster platform. The 4 cylinder cars are easier but 6 cylinder cars require 3-4 different combinations of sockets and extensions and tiny European hands to really get in there.

[nialse]

In the 70's/80's you could fit a person in the engine bay of a Volvo. So, varying degrees of complexity and difficulty to fix things.

[dimal]

I've seen some video comparisons between American cars and Toyotas, and Toyota seemed to have figured out how to make cars a lot easier to maintain than the American companies. I saw one case where changing a simple fuse required several hours of disassembly in the American car but only 30s in the Toyota. It's about priorities. It's about ethics. American companies don't give a fuck, and it shows. And American companies don't give a fuck, because Americans largely don't give a fuck.

[H1Supreme]

I know someone who had an older Chrysler 300, and you had to take a wheel off to change the battery. Baffling. I'm not much of a mechanic, but the Honda's I've owned over the years have all been easy to work on. At least in the engine bay.

[Scoundreller]

Tbh, taking a tire off isn’t that difficult.

BMW can be kinda a pain (its under a liner in the trunk, making you work at weird angles (and part emptying your trunk) but the benefit is your battery isn’t exposed to the elements and probably lasts longer for that reason.

[helterskelter]

I believe there's a modern (GM?) truck out there that has a belt rated for something like 250K miles...but when you have to replace it, the entire engine needs to be removed.

[trashb]

Don't forget one of the latest automotive mistakes, the "wet timing belt". This is a rubber timing belt (not a chain) that runs through your engine oil disintegrating and clogging up your oil filters.

If anyone here owns a car with that system I recommend taking it to your trusted mechanic and discussing with them to do additional preventive maintenance on it.

[warmwaffles]

It's 180k miles. It's the 3.0L Duramax because the oil pump is on the backside of the engine using an oil submersed belt rather than a chain or set of gears. So you have to drop the transmission, exhaust, oil pan, and take the back side of the engine cover to replace a belt that should have been a chain. It _may_ be faster, to simply disconnect everything and pull the motor.

Source: I own one of these engines and I dread having to pay ~3k for this maintenance in 3 years. I like the engine, just not this maintenance ticket item.

[rpcope1]

Sounds like the Colorado. It's a reason they'll pry my S10s, GMT400 and GMT800s from my cold dead hands as they're more reliable, cheaper to service and easier to service.

[hadlock]

In the 1955 Citroen, standard French family car of the era, the timing chain sits behind a cover about 1/2" from the firewall, the whole engine has to come out to change it.