I'm using ConnectX5s for most, and some ConnectX4s in the older servers. Both of those cards have really come down in price in the used/ebay market. I have been playing around with some different optics - I have a bunch of CWDM4s which are very inexpensive and use a single SingleMode pair.... but of course they run hot so if you have them in servers without good air flow you might have problems.
I'm using mostly fiber just because the servers are connected to Cisco 9305 with 72 100g ports.
I wouldn't really call 100Gbit overkill, if you compare it to modern disk drives is about where we should be relative to shared storage/NAS/etc infrastructure people used to run. So yes, being able to share my /home directory across a few dozen machines at my house without a huge perf impact vs using a local drive seems a pretty reasonable use case. Sure its faster than my WAN access, but who cares?
Frankly, 10Gbit is fully 25 years old with, 10GbaseT being 20 years old this year.
Thats ridiculously ancient technology. There is/was a 25/40GbaseT spec too (now 10 years old), which basically no one implemented because like ECC ram (and tape drives, and seem to be trying to do it with harddrives and GPUs) the MBA's have taken over parts of the computer industry and decided that they can milk huge profit margins from technologies which are incrementally more difficult because smaller users just don't matter to their bottom lines. The only reason those MBAs are allowing us to have it now, is because a pretty decent percentage of us can now get 5Gbit+ internet access and our wifi routers can do 1Gbit+ wireless, and the weak link is being able to attach the two.
I did a bit of back of the napkin math/simulation about a possible variable rate Ethernet (ex like NBbaseT, where it has multiple speeds and selects faster one based on line conditions), and concluded that 80+Gbit using modern PHY/DSP's and high symbol rate, multiple bands, techology which is dirt cheap thanks to wifi/bt/etc on fairly short cable distances (ex 30-50M) on CAT8 is entirely possible. And this isn't even fantasy, short cat7 runs are an entire diffrent ballpark from a phone pair, and these days mg.fast/etc have shown 10Gbit+ over that junk.
Agreed - the big thing is 100g is much much cheaper now as so much 100g gear is coming out of datacenters. So many of those older ConnectX4s and 5s, plus lots of switches and optics. 100g really is the new 10g for homelabs.
sponaugle|27 days ago
I'm using mostly fiber just because the servers are connected to Cisco 9305 with 72 100g ports.
omgtehlion|27 days ago
And thanks for pointing at CWDM4, these are quite cheap on ebay now
StillBored|28 days ago
Frankly, 10Gbit is fully 25 years old with, 10GbaseT being 20 years old this year.
Thats ridiculously ancient technology. There is/was a 25/40GbaseT spec too (now 10 years old), which basically no one implemented because like ECC ram (and tape drives, and seem to be trying to do it with harddrives and GPUs) the MBA's have taken over parts of the computer industry and decided that they can milk huge profit margins from technologies which are incrementally more difficult because smaller users just don't matter to their bottom lines. The only reason those MBAs are allowing us to have it now, is because a pretty decent percentage of us can now get 5Gbit+ internet access and our wifi routers can do 1Gbit+ wireless, and the weak link is being able to attach the two.
I did a bit of back of the napkin math/simulation about a possible variable rate Ethernet (ex like NBbaseT, where it has multiple speeds and selects faster one based on line conditions), and concluded that 80+Gbit using modern PHY/DSP's and high symbol rate, multiple bands, techology which is dirt cheap thanks to wifi/bt/etc on fairly short cable distances (ex 30-50M) on CAT8 is entirely possible. And this isn't even fantasy, short cat7 runs are an entire diffrent ballpark from a phone pair, and these days mg.fast/etc have shown 10Gbit+ over that junk.
sponaugle|27 days ago